Self weeding inkjet transfer paper

With this paper you can: Make a One-Step Weedless Transfer:

Self weeding inkjet transfer paper

However there are a few users who have had nothing but trouble with this paper. So here are some of the most common problems and solutions to using this paper. Printing TrimFree When printing TrimFree Transfer Paper, we recommend that you feed the sheet in one at a time through the bypass tray.

Toner Offsetting — One of the most common problems when printing this paper is toner offsetting on the page. TrimFree will not run in plain paper mode for almost all printers. It is likely to run in Heavy 1 to Label 2 mode. When you run TrimFree in plain mode, you will notice that the majority of the image is not printed at all refer to above image and sometimes you get toner on your fingers when you rub it against the image.

Good Print - Printed on the OKI Printer on Labels 1 Mode Toner Offsetting - Printed on OKI in Plain mode If you are getting Toner Offsetting remember to run a few sheets of blank paper through the printer to get rid of the excess toner left in the fuser if the excess toner is not completely cleaned from the fuser unit, all consecutive transfer paper prints will likely be unsuccessful.

Then try the next heavier paper mode. Keep repeating until the problem is gone. Faded or patchy image after printing — This problem is quite rare. If your image looks faded or had white patchy spots in the solid colors and it is not a result of toner offsetting.

It is likely that the paper setting is set too high. Normally when you set the paper setting too high, the paper will jam in the printer.

Self weeding inkjet transfer paper

But in rare cases, it may just produce faded or patchy images. To fix faded or patchy images, simply print on a lower paper setting and this will fix it. It is always recommended to run a few sheets of plain paper whenever you get a failed print.

Pressing onto the Garment. TrimFree is a one step heat press process and can be mastered with practice. The extra repress step with a silicon sheet is to ensure better wash resistance.

When pressing TrimFree, ensure that you follow the instructions given to you. In the rare case where you received no instructions, please contact Joto for instructions. Some of the most common problems when pressing TrimFree are: Polymer Window on the unimaged areas.

If you get a polymer window or partial polymer window on your image where there is no toner, there are two possible reasons for this. When peeling, the wait was too long. We recommend peeling the paper seconds after heat pressing. This wait will vary depending on the fabric.

For lighter thinner fabrics like tank tops, you could almost peel the paper immediately. For heavier thicker fabrics, such as sweaters and hoodies, you need to wait the full 10 seconds to peel. Waiting too long to peel will result in some polymer window being left behind.

Self-weeding transfer paper

And if you wait too long, the backing paper may stick to the shirt and peeling the backing paper off will be next to impossible. If the temperature is too high or the press time too long, it will also leave a polymer window on the shirt see above image. If you press TrimFree at F or 25 seconds, it is most certainly going to leave a polymer window where there is no toner.

Polymer Window - Black image printed on blue to better show polymer window when too much heat is applied F for 25secs Perfect Black Only TrimFree Image F for 30 seconds So if you get a large visible polymer window, check your press temperature to ensure it is not too high.

Post Archive

And check to make sure that you have not waited too long to peel. But there is no fixing a pressed image where too much heat has been applied to the transfer. Incomplete Image Transfer If you get an incomplete image transfer, there are 4 reasons why this could be: You used drop shadows, gradients or skin tones.

This is not a defect in the paper, it is a limitation of the paper because of how drop shadows, gradients, or skin tones are created using toner. TrimFree will only print solid colors consistently.The self-weeding feature of ImageClip for Lights allows it to transfer a super-soft and light weight image only where your design is printed -- and the two simple application press steps deliver easy and consistent results, for an overall durable image and print output.

Topcut is a user-friendly self weeding transfer paper Shock line for light colored fabrics. Ideal for most oil or oil less laser color printers. Perfectly outlines texts and designs in strong and full colors and images, even with gradients (maximum 30%).

Self weeding inkjet transfer paper

Our core business focuses on the production of topquality, coated presentation papers and films in a number of variations, ranging from inkjet transfer paper, Color laser transfer paper, Eco-solvent Printable Flex and Cuttable PU Flex etc.

heat transfer vinyl & PAPER With our range of heat transfer media you can print on just about anything. We have laser heat transfer paper for printing onto t-shirts, garments & other surfaces, self weeding papers and standard papers. Self Weeding Paper, Heat Transfer Paper, Transfer Paper manufacturer / supplier in China, offering Hot Sale High Quality Self Weeding Heat Transfer Paper, Wholesale Water Based Printing Sublimation Ink for Epson Surecolor Printer, China Factory Direct Supply Sublimation Dye Ink Cheap Price and so on.

TrimFree is a self-weeding laser transfer paper for white or light colored fabrics. What does this mean? Although transfer papers have improved, greatly reducing the visibility of the unimaged areas of the design, it is still necessary to trim the paper to minimize the amount of polymer background that is transferred to the garment.

Laser Heat Transfer Paper For Darks